Take Care of The Common Problems When Use Your Laser Cutting Machine
Laser cutting machine is a newest machine with high technology. This machine use the invisible light beam to replace the traditional knife to help people cut they patterns they want onto the different materials. This machine has many advantages which can help you improve your working efficiency, decrease processing cost. While same as the rotary heat press machine, it also always have many problems that you should better take care when use your laser cutting machine. Here in order to let you know more I will list them carefully and share you how to solve in a right way.
1. Cutting Effect is Not Good Enough
Power set is too small, the potentiometer twist, light, the lens is dirty, focus lens installed anti, focal length, laser power, laser tube power attenuation, water temperature is too high, voltage instability and so on according to the actual situation determined by Jane as deep.
2. Machine Can't Be Connected to The Device
Whether to install the board driver, USB cable or cable is plugged in, USB cable or network cable is bad, bad adapter board, board, etc.
3. Cutting Graphic Deformation And Cutting Overlap
Sync wheel screw loose, motor break, motor bad, drive, voltage and so on
4. Device Can Not Start
Whether the emergency stop is bouncing, whether the external circuit is connected, whether the internal air is open, whether it is turned on, or the sound of the snapping, etc. Please check the main contact and control the transformer and so on; water leakage caused by the water leakage 107 pump short circuit, the use of indoor air open too small.
5. High Voltage Line Ignition
This problem is really a headache, I suggest that the high-voltage lines outside the high pressure insulated casing
6. Marking Position Offset
Vibration axis X axis or Y axis position offset, find the center point according to the actual offset direction to adjust the XY axis position
7. Laser Tube Connection Error
In the connector (internal line without desoldering short circuit), the power line (left and right negative negative with the ground with the same), the water connection normal restart the chiller and equipment can not be connected after the normal is twenty-five pin connector The problem of connecting the circuit board is broken or is not compatible with the board and the non-encrypted tube is not compatible with the board
8.Cutting Machine Cutting Dislocation
1.) Feed cutting error
First, The feed step step distance = measured length * the original step / real length (set the feed length)
Second, check the feed shaft of the timing belt with the wheel with the motor timing belt locking wheel Whether the loosening of the three is rolling net loose and feed the axis between the relative sliding there is to see if there is a card phenomenon
2.) No feed cutting error
First, the cart motor or optical axis synchronous wheel loose
Second, lost step phenomenon may be the processing speed of the air speed or acceleration is too large may be too large motor vehicle line contact may be a reminder The current is too small may be bad drive or bad motor bad motor bad and lost the phenomenon of less
9. Feeding Length
Feeding machine length feed is generally the photoelectric switch is bad or the photoelectric switch light sensitivity is not on the feeder photoelectric switch light sensitivity adjustable in the case of long closed up and down the two switches at the same time when the light when the feeder began to work when the light sensitivity is too Sensitive, even if there is a cutting material will be blocked for the light through the light so the length of the feed at this time to adjust the photoelectric switch wiring sensitivity adjustment knob to adjust the material to block when the photoelectric switch indicator light can be.
Okay, These all above are my list of the common problems of the usage of laser cutting machine and some small tips about how to solve them . If you have any needs or questions welcome to contact us at any time. We will provide you with the best quality product and service. Hope my article can be useful to you. Thank you for your reading.
Whatsapp:+8618752006819
Website :www.heatsub.com
Facebook: zeo(章江徽）
Email: zeo@feiyuepaper.com
1. Cutting Effect is Not Good Enough
Power set is too small, the potentiometer twist, light, the lens is dirty, focus lens installed anti, focal length, laser power, laser tube power attenuation, water temperature is too high, voltage instability and so on according to the actual situation determined by Jane as deep.
2. Machine Can't Be Connected to The Device
Whether to install the board driver, USB cable or cable is plugged in, USB cable or network cable is bad, bad adapter board, board, etc.
3. Cutting Graphic Deformation And Cutting Overlap
Sync wheel screw loose, motor break, motor bad, drive, voltage and so on
4. Device Can Not Start
Whether the emergency stop is bouncing, whether the external circuit is connected, whether the internal air is open, whether it is turned on, or the sound of the snapping, etc. Please check the main contact and control the transformer and so on; water leakage caused by the water leakage 107 pump short circuit, the use of indoor air open too small.
5. High Voltage Line Ignition
This problem is really a headache, I suggest that the high-voltage lines outside the high pressure insulated casing
6. Marking Position Offset
Vibration axis X axis or Y axis position offset, find the center point according to the actual offset direction to adjust the XY axis position
7. Laser Tube Connection Error
In the connector (internal line without desoldering short circuit), the power line (left and right negative negative with the ground with the same), the water connection normal restart the chiller and equipment can not be connected after the normal is twenty-five pin connector The problem of connecting the circuit board is broken or is not compatible with the board and the non-encrypted tube is not compatible with the board
8.Cutting Machine Cutting Dislocation
1.) Feed cutting error
First, The feed step step distance = measured length * the original step / real length (set the feed length)
Second, check the feed shaft of the timing belt with the wheel with the motor timing belt locking wheel Whether the loosening of the three is rolling net loose and feed the axis between the relative sliding there is to see if there is a card phenomenon
2.) No feed cutting error
First, the cart motor or optical axis synchronous wheel loose
Second, lost step phenomenon may be the processing speed of the air speed or acceleration is too large may be too large motor vehicle line contact may be a reminder The current is too small may be bad drive or bad motor bad motor bad and lost the phenomenon of less
9. Feeding Length
Feeding machine length feed is generally the photoelectric switch is bad or the photoelectric switch light sensitivity is not on the feeder photoelectric switch light sensitivity adjustable in the case of long closed up and down the two switches at the same time when the light when the feeder began to work when the light sensitivity is too Sensitive, even if there is a cutting material will be blocked for the light through the light so the length of the feed at this time to adjust the photoelectric switch wiring sensitivity adjustment knob to adjust the material to block when the photoelectric switch indicator light can be.
Okay, These all above are my list of the common problems of the usage of laser cutting machine and some small tips about how to solve them . If you have any needs or questions welcome to contact us at any time. We will provide you with the best quality product and service. Hope my article can be useful to you. Thank you for your reading.
Whatsapp:+8618752006819
Website :www.heatsub.com
Facebook: zeo(章江徽）
Email: zeo@feiyuepaper.com
评论
发表评论